SimLab Tutorials - Linear Transient Heat Transfer Analysis

Split faces using chaining edges; create a transient heat transfer solution; create material with thermal properties; define initial conditions; apply thermal loads such as time dependent heat flux and convection; define solver settings and analyze

All related resources

Flux Tutorial: Electric Motor Design Analysis Tutorial

Flux Tutorial: Electric Motor Design Analysis Tutorial

Video shows how to set up a simulation of a brushless permanent magnet motor to do a cogging torque analysis using Altair Flux™.

Tutorials
Altair Flux Actuator Design Tutorial

Altair Flux Actuator Design Tutorial

Complete set up, analysis, and post-processing of an actuator in Altair Flux™ 3D.

Tutorials
Altair Flux User Environment and Workflow

Altair Flux User Environment and Workflow

This brief video explains the general philosophy of how Altair Flux™ is used starting. The video also shows how commands for geometry, mesh generation and general model setup can be accessed.

Tutorials
Catapult Tutorial 2: Actuators, Motors and Springs

Catapult Tutorial 2: Actuators, Motors and Springs

Using Inspire Motion, learn how to set up a motion simulation of a catapult. This video covers the setup of actuators, motors and springs

Tutorials
Catapult Tutorial 1: Ground, Rigid Groups, Joints and Contacts and Results

Catapult Tutorial 1: Ground, Rigid Groups, Joints and Contacts and Results

Using Inspire Motion, learn how to set up a motion simulation of a medieval catapult. This video covers the setup of ground, rigid groups, joints and contacts, and results

Tutorials
VSim Tutorial Videos

VSim Tutorial Videos

Calculate Pi-mode Frequency in a Simulated SRF Cavity using VSim

Tutorials
AFDEX & HyperStudy - Optimization Tutorial

AFDEX & HyperStudy - Optimization Tutorial

Tutorial on how to use AFDEX and HyperStudy together for two stage hot-forging process of an automotive gear wheel.

Tutorials
SimLab sT for Computational Fluid Dynamics

SimLab sT for Computational Fluid Dynamics

Process-driven setup, capture complex phenomena and investigate fluid flows interactively.

Tutorials
SimLab sT Software Overview

SimLab sT Software Overview

Overview of SimLab sT key capabilities like CAD import, automatic meshing, robust analysis and interactive results

Tutorials
SimLab sT Vibro-Acoustic Analysis

SimLab sT Vibro-Acoustic Analysis

Fully automated process. Create the ideal mesh for acoustic analysis, obtain electromagnetic excitation and instantly calculate acoustic noise.

Tutorials
SimLab sT from CAD Concept to Optimized Structures

SimLab sT from CAD Concept to Optimized Structures

Automatically generate the best possible mesh, define manufacturing constraints and easily evaluate results.

Tutorials
SimLab sT: Results Accuracy

SimLab sT: Results Accuracy

Local refinements to increase accuracy.

Tutorials
ProteusDS Tutorial Videos

ProteusDS Tutorial Videos

DSA and Altair Engineering are pleased to bring you a free collection of tutorials to become better acquainted with ProteusDS.

Tutorials
AVL CRUISE™ M Tutorial Videos

AVL CRUISE™ M Tutorial Videos

AVL and Altair Engineering are pleased to bring you a free collection of tutorials to become better acquainted with AVL CRUISE™ M.

Tutorials
Design Balance and Requirements Verification with XLDyn

Design Balance and Requirements Verification with XLDyn

Tutorial video for design balance and requirements verification with XLDyn.

Tutorials
Basics of LOGEengine

Basics of LOGEengine

Introductory tutorial for learning how to apply LOGEengine, with a diesel engine example.

Tutorials
Inspire Extrude Metal Workflow - Step 4

Inspire Extrude Metal Workflow - Step 4

Step 4: Perform Extrusion Simulation

Tutorials
Inspire Extrude Polymer Workflow - Step 3

Inspire Extrude Polymer Workflow - Step 3

Step 3: Process Data and Run Analysis

Tutorials
Inspire Extrude Polymer Workflow - Step 2

Inspire Extrude Polymer Workflow - Step 2

Step 2: Material Selection and Organizing Layers

Tutorials
Inspire Extrude Metal Workflow - Step 5

Inspire Extrude Metal Workflow - Step 5

Step 5: Analyze Results

Tutorials
Inspire Extrude Metal Workflow - Step 2

Inspire Extrude Metal Workflow - Step 2

Step 2: Extract Bearing

Tutorials
Inspire Extrude Polymer Workflow - Step 4

Inspire Extrude Polymer Workflow - Step 4

Step 4: Run Post Processing

Tutorials
Inspire Extrude Polymer Workflow - Step 1

Inspire Extrude Polymer Workflow - Step 1

Step 1: Import Load and Extract Volumes

Tutorials
Inspire Extrude Metal Workflow - Step 3

Inspire Extrude Metal Workflow - Step 3

Step 3: Create Billet and Material Selection

Tutorials
Inspire Extrude Metal Workflow - Step 1

Inspire Extrude Metal Workflow - Step 1

Step 1: Load Orientation

Tutorials
Optenni Lab Tutorial - Aperture Tuning Using a Switch

Optenni Lab Tutorial - Aperture Tuning Using a Switch

Antenna tuners are commonly used especially to handle carrier aggregation (CA) schemes in handsets. Optenni Lab is designed to setup and solve aperture and impedance tuner design problems using either switch or a variable capacitor.

Tutorials
LOGEresearch Tutorial Video

LOGEresearch Tutorial Video

LOGE AB and Altair are pleased to bring you a free online tutorial video to become better acquainted with the software

Tutorials
Virfac® Training Videos

Virfac® Training Videos

GeonX and Altair Engineering are pleased to bring you a free collection of tutorials to become better acquainted with the software.

Tutorials
CES Selector Training Videos

CES Selector Training Videos

Granta Design and Altair Engineering are pleased to bring you a free collection of tutorials to become better acquainted with the software.

Tutorials
Inspire Extrude Metal 2017.3 Help and Tutorials

Inspire Extrude Metal 2017.3 Help and Tutorials

Explore help and tutorial resources to learn how to navigate through Inspire Extrude Metal and its features and tools.

Tutorials
How to Choose Modules in AFDEX

How to Choose Modules in AFDEX

Short tutorial for helping decide which AFDEX module is best for the type of analysis necessary.

Tutorials
Inspire Extrude 2017 Training Manual

Inspire Extrude 2017 Training Manual

In this training manual you will learn the step by step process used in Inspire Extrude in order to run a successful extrusion simulation. The manual will cover an overview, features and all the basic tools within the software.

Tutorials
MADYMO Online Tutorials

MADYMO Online Tutorials

TASS International is pleased to bring you a free collection of tutorials to become better acquainted with the software.

Tutorials
Basics of LOGEresearch

Basics of LOGEresearch

Introductory tutorial for learning the basics of LOGEresearch.

Tutorials
AFDEX Tutorials

AFDEX Tutorials

Collection of tutorials with demo files to help users learn how to use AFDEX for 2D and 3D automatic multi-stage cold forging, 2D non-isothermal analysis (hot forging), 2D plate forging, 3D automatic multi-stage hot forging and 3D cold forging.

Tutorials
Charge Tutorial - Electrostatic Simulation of a Vacuum Circuit Breaker

Charge Tutorial - Electrostatic Simulation of a Vacuum Circuit Breaker

Fieldscale Charge is very simple to use for any electrostatic simulation. This step-by-step tutorial example shows the electrostatic simulation of the arc extinguish chamber of a vacuum circuit breaker.

Tutorials
ESAComp Wing Box Tutorial

ESAComp Wing Box Tutorial

Short video tutorial to illustrate how to analyze a wing box using HyperMesh and ESAComp.

Tutorials
Tutorial on Max 1st Principle Stress with StressCheck

Tutorial on Max 1st Principle Stress with StressCheck

Tutorial presentation to help perform 1st principle stress using StressCheck.

Tutorials
Step by Step Tutorial for Using NovaFlow&Solid with solidThinking Inspire

Step by Step Tutorial for Using NovaFlow&Solid with solidThinking Inspire

This document provides an in-depth description of how NovaFlow&Solid can be used alongside Inspire to help users create better parts more efficiently.

Tutorials
Inspire 2018 Help and Tutorials - Windows

Inspire 2018 Help and Tutorials - Windows

In these lessons you will learn to: apply supports and forces, define design spaces, run optimization, analysis, explore shapes, and export results to Evolve or an STL file.

Tutorials
Have a Question? If you need assistance beyond what is provided above, please contact us.

Be the first to know

Subscribe to our newsletter to learn about product training, news, events, and more!